Load banks: your solution for testing and maintaining your generator sets<\/h1>\n<\/div>RECEIVE A PERSONALIZED QUOTE WITHIN 24H<\/span><\/a><\/div>\n<\/div><\/div>![\"Generator\"](\"https:\/\/www.mdresistor.com\/wp-content\/uploads\/2020\/12\/groupe-electrogene-min.jpg\" "\\"groupe")
<\/span><\/div><\/div><\/div><\/div><\/div>METAL DEPLOYE RESISTOR offers load banks or test banks.
\nThey allow testing the operation of equipment such as generators<\/strong> , whether emergency or power supply, for reasons of:<\/p>\n\n- security<\/li>\n
- maintenance<\/li>\n
- conformity<\/li>\n
- risk anticipation<\/li>\n<\/ul>\n
This guarantees you, in the long term, correct operation of your equipment<\/strong> and a reduction in breakdowns and destruction of your equipment.<\/p>\nYou are a generator set specialist<\/strong> (rental company, maintainer,\u2026)?
\nYour solution is the use of load bank for generator set<\/strong> adapted to your needs, up to 3300 kVA.<\/p>\n<\/div><\/div><\/div><\/div><\/div>Generator test: for preventive and corrective maintenance<\/h2>\n<\/div>Generators rarely run at full speed. It is during prolonged operation at low load as risks of deterioration may appear<\/strong> as :<\/p>\n\n- clogging of the injectors,<\/li>\n
- the accumulation of humidity and carbon, in particular in the combustion chambers and the exhaust system,<\/li>\n
- or even the icing of cylinders.<\/li>\n<\/ul>\n
The solution is to rev up the installation to full capacity<\/strong> to determine its maximum power over a given time.
\nIt is the use of load banks, which will allow preventive and curative maintenance<\/strong>by reducing risk of failure <\/strong> by maintaining your equipment at nominal performance.<\/p>\n<\/div><\/div><\/div><\/div><\/div>Why use a load bank for a generator set? Test it, maintain it, ballast it<\/h2>\n<\/div>Test a generator<\/h3>\n
The load bank tests a group to verify that it can still deliver its full power<\/strong> .<\/p>\nThis is valid for any type of generator:<\/p>\n
\n- A production \/ rental generator set<\/strong> . Here, it is a matter of ensuring the proper operation of the equipment let to each customer,<\/li>\n
- An emergency generator, <\/strong>seldom used, seldom tested.<\/li>\n<\/ul>\n
The full load test guarantees:<\/p>\n
\n- the proper functioning<\/strong> of a generator<\/li>\n
- its power handling<\/strong> , without cutting or disturbing the network by a real test.<\/li>\n<\/ul>\n
In fact, most faults and failures only occur at full load. A no-load test would not diagnose them, while further fouling the generator set.<\/p>\n
Maintain a generator<\/h3>\nClean out the engine<\/h4>\n
An engine which runs after a long period at low load does not reach its optimum operating temperature. So there is a risk that it will get dirty: we use the term \u201c wet stacking<\/strong> \u201d. It is then necessary “flush” with a minimum of 80% of the nominal power<\/strong> .<\/p>\nBreaking in the engine<\/h4>\n
After having performed extensive maintenance, it is important to break in the engine using a test bank.<\/p>\n<\/div><\/div><\/div>
![\"SDMO](\"https:\/\/www.mdresistor.com\/wp-content\/uploads\/2020\/12\/groupe-electrogene-SDMO-min-400x254.png\" "\\"groupe")
<\/span><\/div><\/div><\/div>Ballasting a generator<\/h3>\n
If it operates for long periods at low load, the generator set should be subjected toballasting<\/strong> . This makes it possible to measure the power supplied to the network and thus trigger the resistance steps necessary to reach a minimum power of 30% to 50% of the generator’s nominal<\/strong> power.<\/p>\nTherefore, the generator set operates at the temperature that suits it, which:<\/p>\n
\n- limits its fouling,<\/strong><\/li>\n
- ensures better performance.<\/strong><\/li>\n<\/ul>\n<\/div><\/div><\/div><\/div><\/div>
A range of load banks to test all electrical equipment<\/h2>\n<\/div>
<\/span><\/div><\/div><\/div><\/div><\/div>METAL DEPLOYE RESISTOR offers load banks or test banks. This guarantees you, in the long term, correct operation of your equipment<\/strong> and a reduction in breakdowns and destruction of your equipment.<\/p>\n You are a generator set specialist<\/strong> (rental company, maintainer,\u2026)? Generators rarely run at full speed. It is during prolonged operation at low load as risks of deterioration may appear<\/strong> as :<\/p>\n The solution is to rev up the installation to full capacity<\/strong> to determine its maximum power over a given time. The load bank tests a group to verify that it can still deliver its full power<\/strong> .<\/p>\n This is valid for any type of generator:<\/p>\n The full load test guarantees:<\/p>\n In fact, most faults and failures only occur at full load. A no-load test would not diagnose them, while further fouling the generator set.<\/p>\n An engine which runs after a long period at low load does not reach its optimum operating temperature. So there is a risk that it will get dirty: we use the term \u201c wet stacking<\/strong> \u201d. It is then necessary “flush” with a minimum of 80% of the nominal power<\/strong> .<\/p>\n After having performed extensive maintenance, it is important to break in the engine using a test bank.<\/p>\n<\/div><\/div><\/div> If it operates for long periods at low load, the generator set should be subjected toballasting<\/strong> . This makes it possible to measure the power supplied to the network and thus trigger the resistance steps necessary to reach a minimum power of 30% to 50% of the generator’s nominal<\/strong> power.<\/p>\n Therefore, the generator set operates at the temperature that suits it, which:<\/p>\n
\nThey allow testing the operation of equipment such as generators<\/strong> , whether emergency or power supply, for reasons of:<\/p>\n\n
\nYour solution is the use of load bank for generator set<\/strong> adapted to your needs, up to 3300 kVA.<\/p>\n<\/div><\/div><\/div><\/div><\/div>Generator test: for preventive and corrective maintenance<\/h2>\n<\/div>
\n
\nIt is the use of load banks, which will allow preventive and curative maintenance<\/strong>by reducing risk of failure <\/strong> by maintaining your equipment at nominal performance.<\/p>\n<\/div><\/div><\/div><\/div><\/div>Why use a load bank for a generator set? Test it, maintain it, ballast it<\/h2>\n<\/div>
Test a generator<\/h3>\n
\n
\n
Maintain a generator<\/h3>\n
Clean out the engine<\/h4>\n
Breaking in the engine<\/h4>\n
<\/span><\/div><\/div><\/div>Ballasting a generator<\/h3>\n
\n
A range of load banks to test all electrical equipment<\/h2>\n<\/div>